Rabbit OP7100 User Manual Page 85
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
OP7100 Installation
85
FD
JP5
12
0 V/GND
FGND
JP5
12
0 V/GND
FGND
Bezel/Casing to Power Supply GND
Bezel/Casing to External Ground
External
Ground
External
Ground
JP4
JP5
JP3
Figure 6-1 shows the location of header JP5.
Figure 6-1. Location of Header JP5
Installation Guidelines
When possible, following these guidelines when mounting an OP7100.
1. Leave sufficient ventilation space
2. Do not install the OP7100 directly above machinery that radiates a lot
of heat (for example, heaters, transformers, and high-power resistors).
3. Leave at least 8" (20 cm) distance from electric power lines and even
more from high-voltage devices.
4. When installing the OP7100 near devices with strong electrical or
magnetic fields (such as solenoids), allow a least 3" (8 cm), more if
necessary.
The OP7100 has strong environmental resistance and high reliability, but
you can maximize system reliability by avoiding or eliminating the
following conditions at the installation site.
• Abrupt temperature changes and condensation
• Ambient temperatures exceeding a range of 0°C to 50°C
• Relative humidity exceeding a range of 25% to 65%
• Strong magnetism or high voltage
• Corrosive gasses
• Direct vibration or shock
• Excessive iron dust or salt
• Spray from harsh chemicals
- User’s Manual 1
- OP7100 User’s Manual 2
- Trademarks 2
- TABLE OF CONTENTS 3
- Chapter 4: Software 51 4
- Chapter 6: Installation 83 5
- Table of Contents OP7100 6
- ABOUT THIS MANUAL 7
- Acronyms 8
- Conventions 9
- OP7100x 10
- About This Manual 10
- OVERVIEW 11
- Features 13
- Software 14
- CE Compliance 15
- OP710016 16
- Overview 16
- GETTING STARTED 17
- Initial OP7100 Setup 18
- OP7100 SERIES 19
- DISPLAY/CONTROLLER 19
- 1999 Dec 31 19
- 23 : 59 : 59 19
- OP710020 20
- Getting Started 20
- Conductor 21
- Running Dynamic C 22
- HARDWARE 23
- OP7100 Subsystems Overview 24
- Power Management 25
- ADM691 Supervisor Chip 26
- OP7100 Hardware 27
- OP710028 28
- Hardware 28
- System Reset 29
- Liquid Crystal Display (LCD) 30
- Background 31
- Coordinate Systems 32
- LCD Controller Chip 32
- PRE-2006 33
- Keypad Interface 34
- Digital I/O 35
- Serial Communication 36
- RS-485 on 37
- RS-232 on 37
- RS-232 Communication 38
- RS-485 Communication 40
- Use of the Serial Ports 42
- Z180s can be programmed to 43
- ASCI Status Registers 45
- /DCD0 (Channel 0 only) 46
- ASCI Control Register A 47
- ASCI Control Register B 48
- OP710050 50
- SOFTWARE 51
- Supplied Software 52
- Real-Time Clock (RTC) 54
- Flash EPROM 55
- Dynamic C 32 Libraries 56
- OP7100 Software 57
- OP710058 58
- Software 58
- OP710060 60
- OP710062 62
- OP710064 64
- Keypad Programming 65
- Using Dynamic C v. 5.xx 66
- Macro Description Effect 67
- OP710068 68
- OP71.LIB 70
- OP710072 72
- Upgrading Dynamic C 73
- OP710074 74
- GRAPHICS PROGRAMMING 75
- Drawing Primitives 76
- Initialization 76
- Font and Bitmap Conversion 78
- Printing Text 80
- OP710082 82
- Graphics Programming 82
- INSTALLATION 83
- Grounding 84
- Installation Guidelines 85
- Mounting 86
- OP7100 Bezel/Gasket 87
- OP710088 88
- Installation 88
- TROUBLESHOOTING 89
- Out of the Box 90
- Dynamic C Will Not Start 91
- Dynamic C Loses Serial Link 91
- OP7100 Repeatedly Resets 91
- Common Programming Errors 92
- SPECIFICATIONS 93
- LCD aperture is 122 x 92 mm 94
- General Specifications 95
- Header Description 96
- OP7100 Specifications 97
- OP710098 98
- Specifications 98
- APPENDIX C: MEMORY 99
- OP7100 Memory 100
- Operation 101
- Execution Time 101
- Memory Map 102
- Address Name Description 103
- OP7100104 104
- Other Registers 105
- Interrupt Vectors 106
- Interrupt Priorities 107
- OP7100108 108
- SERIAL INTERFACE BOARD 109
- Introduction 110
- External Dimensions 111
- BACKUP BATTERY 113
- Replacing the Lithium Battery 114
- Battery Cautions 115
- OP7100116 116
- Backup Battery 116
- OP7100 Index 117
- OP7100118 118
- OP7100120 120
- OP7100122 122
- OP7100124 124
- SCHEMATICS 125
- XX0000Schematics 126
Related products and manuals for TVs & monitors Rabbit OP7100
TVs & monitors Rabbit OP7100 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 1.182 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals