Rabbit OP7100 User Manual Page 2
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
eDisplay (OP7200)
Digi International Inc.
www.rabbit.com
OP7200 User’s Manual
Part Number 019-0116 • 081115–L • Printed in U.S.A.
©2002–2008 Digi International Inc. • All rights reserved.
Digi International reserves the right to make changes and
improvements to its products without providing notice.
Trademarks
Rabbit and Dynamic C are registered trademarks of Digi International Inc.
Rabbit 2000, RabbitCore, and RabbitNet are trademarks of Digi International Inc.
No part of the contents of this manual may be reproduced or transmitted in any form or by any means
without the express written permission of Digi International.
Permission is granted to make one or more copies as long as the copyright page contained therein is
included. These copies of the manuals may not be let or sold for any reason without the express written
permission of Digi International.
The latest revision of this manual is available on the Rabbit Web site, www.rabbit.com,
for free, unregistered download.
- User’s Manual 1
- OP7200 User’s Manual 2
- TABLE OF CONTENTS 3
- Chapter 4. Software 47 4
- Appendix B. Power Supply 139 5
- Appendix D. RabbitNet 151 5
- Index 161 5
- Schematics 165 5
- 1. INTRODUCTION 7
- Table 1. OP7200 Models 8
- Figure 1. OP7200 Tool Kit 9
- A compat 10
- User’s Manual 5 11
- 1.4 CE Compliance 12
- User’s Manual 7 13
- 8 eDisplay (OP7200) 14
- 2. GETTING STARTED 15
- 10 eDisplay (OP7200) 16
- User’s Manual 11 17
- PC COM port 18
- 2.4 Installing Dynamic C 19
- 2.5 Starting Dynamic C 19
- 2.6 PONG.C 20
- 2.7 Where Do I Go From Here? 20
- 2.8 Remove Battery Tab 21
- SETRTCKB.C 21
- 16 eDisplay (OP7200) 22
- 3. SUBSYSTEMS 23
- 3.1 OP7200 Pinouts 24
- 3.2 Indicators 25
- 3.3 Digital I/O 26
- Digital Input Voltage 27
- SINKING OUTPUTS 28
- SOURCING OUTPUTS 28
- CAUTION: Disconnect power 29
- User’s Manual 25 31
- Table 4. Bipolar Voltages 33
- 3.4.3.1 Modes 34
- User’s Manual 29 35
- 30 eDisplay (OP7200) 36
- 32 eDisplay (OP7200) 38
- 3.5 Serial Communication 39
- 34 eDisplay (OP7200) 40
- 36 eDisplay (OP7200) 42
- ETHERNET 43
- DIAG connector on 44
- 3.6 Memory 45
- PRE-2006 OP7200 46
- CURRENT OP7200 46
- 3.8 Keypad 47
- 3.9 OP7200 CPLD 48
- User’s Manual 43 49
- 3.10 Programming Cable 50
- 3.11 Other Hardware 51
- 46 eDisplay (OP7200) 52
- 4. SOFTWARE 53
- 48 eDisplay (OP7200) 54
- 4.1.1.2 Upgrades 55
- 50 eDisplay (OP7200) 56
- User’s Manual 51 57
- 4.3 Sample Programs 58
- 54 eDisplay (OP7200) 60
- User’s Manual 55 61
- 56 eDisplay (OP7200) 62
- 4.4 OP7200 Libraries 63
- 4.5 OP7200 Function APIs 64
- 4.5.2 Digital I/O 65
- OUT0–OUT7) 65
- 60 eDisplay (OP7200) 66
- 4.5.3 LEDs 68
- User’s Manual 67 73
- 70 eDisplay (OP7200) 76
- 0 if successful 78
- User’s Manual 77 83
- User’s Manual 95 101
- PARAMETER 101
- SEE ALSO 101
- 4.5.7 Keypad Functions 102
- 1 when completed 106
- RETURN VALUE 108
- 102 eDisplay (OP7200) 108
- PARAMETERS 108
- TsScanState function 116
- 4.7 RabbitNet Port 117
- 112 eDisplay (OP7200) 118
- 5. USING THE TCP/IP FEATURES 119
- <Ctrl-Y> 120
- 5.2 TCP/IP Sample Programs 121
- IP Address : 10.10.6.101 122
- Netmask : 255.255.255.0 122
- Default gateway : 10.10.6.1 122
- Start > Run 123
- 118 eDisplay (OP7200) 124
- 5.3 Where Do I Go From Here? 125
- 120 eDisplay (OP7200) 126
- CARE GUIDELINES 127
- 6.2 Installation Guidelines 128
- 6.3 Mounting Instructions 129
- OP7200 Bezel/Gasket 130
- 6.4 Care Guidelines 131
- 126 eDisplay (OP7200) 132
- APPENDIX A. SPECIFICATIONS 133
- 128 eDisplay (OP7200) 134
- User’s Manual 129 135
- A.1.1 Physical Mounting 136
- A.2 Conformal Coating 137
- A.3 Jumper Configurations 138
- User’s Manual 133 139
- 134 eDisplay (OP7200) 140
- Backup Battery 141
- A.5 I/O Address Assignments 143
- 138 eDisplay (OP7200) 144
- APPENDIX B. POWER SUPPLY 145
- 140 eDisplay (OP7200) 146
- /RESET output signal 147
- External 148
- Figure B-4. VRAM Switch 150
- B.3 Chip Select Circuit 151
- 146 eDisplay (OP7200) 152
- APPENDIX C 153
- DIGIN.C Sample Program 154
- DIGOUT.C Sample Program 155
- Jumpers: 156
- H1: None 156
- H2: As shown 156
- APPENDIX D. RABBITNET 157
- 152 eDisplay (OP7200) 158
- D.2 Physical Implementation 159
- D.3 Function Calls 160
- D.3.1 Status Byte 166
- User’s Manual 161 167
- 162 eDisplay (OP7200) 168
- User’s Manual 163 169
- 164 eDisplay (OP7200) 170
- SCHEMATICS 171
Related products and manuals for TVs & monitors Rabbit OP7100
TVs & monitors Rabbit OP7100 User Manual
(41 pages)
(41 pages)
TVs & monitors Rabbit OP7100 User Manual
(126 pages)
(126 pages)
TVs & monitors Rabbit OP7100 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 1.154 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals