Rabbit OP7100 User Manual download pdf (Page 73)

User’s Manual 67

value1 is the first A/D converter channel value (0–2047).

volts1 is the voltage or current corresponding to the first A/D converter channel value.

value2 is the second A/D converter channel value (0–2047).

volts2 is the voltage or current corresponding to the first A/D converter channel value.

RETURN VALUE

0 if successful.

-1 if not able to make calibration constants.

SEE ALSO

anaIn, anaInVolts, brdInit, anaInmAmps, anaInDiff, anaInEERd, anaInEEWr

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 171 172

User’s Manual 1
OP7200 User’s Manual 2
TABLE OF CONTENTS 3
Chapter 4. Software 47 4
Appendix B. Power Supply 139 5
Appendix D. RabbitNet 151 5
Index 161 5
Schematics 165 5
1. INTRODUCTION 7
Table 1. OP7200 Models 8
Figure 1. OP7200 Tool Kit 9
A compat 10
User’s Manual 5 11
1.4 CE Compliance 12
User’s Manual 7 13
8 eDisplay (OP7200) 14
2. GETTING STARTED 15
10 eDisplay (OP7200) 16
User’s Manual 11 17
PC COM port 18
2.4 Installing Dynamic C 19
2.5 Starting Dynamic C 19
2.6 PONG.C 20
2.7 Where Do I Go From Here? 20
2.8 Remove Battery Tab 21
SETRTCKB.C 21
16 eDisplay (OP7200) 22
3. SUBSYSTEMS 23
3.1 OP7200 Pinouts 24
3.2 Indicators 25
3.3 Digital I/O 26
Digital Input Voltage 27
SINKING OUTPUTS 28
SOURCING OUTPUTS 28
CAUTION: Disconnect power 29
User’s Manual 25 31
Table 4. Bipolar Voltages 33
3.4.3.1 Modes 34
User’s Manual 29 35
30 eDisplay (OP7200) 36
32 eDisplay (OP7200) 38
3.5 Serial Communication 39
34 eDisplay (OP7200) 40
36 eDisplay (OP7200) 42
ETHERNET 43
DIAG connector on 44
3.6 Memory 45
PRE-2006 OP7200 46
CURRENT OP7200 46
3.8 Keypad 47
3.9 OP7200 CPLD 48
User’s Manual 43 49
3.10 Programming Cable 50
3.11 Other Hardware 51
46 eDisplay (OP7200) 52
4. SOFTWARE 53
48 eDisplay (OP7200) 54
4.1.1.2 Upgrades 55
50 eDisplay (OP7200) 56
User’s Manual 51 57
4.3 Sample Programs 58
54 eDisplay (OP7200) 60
User’s Manual 55 61
56 eDisplay (OP7200) 62
4.4 OP7200 Libraries 63
4.5 OP7200 Function APIs 64
4.5.2 Digital I/O 65
OUT0–OUT7) 65
60 eDisplay (OP7200) 66
4.5.3 LEDs 68
User’s Manual 67 73
70 eDisplay (OP7200) 76
0 if successful 78
User’s Manual 77 83
User’s Manual 95 101
PARAMETER 101
SEE ALSO 101
4.5.7 Keypad Functions 102
1 when completed 106
RETURN VALUE 108
102 eDisplay (OP7200) 108
PARAMETERS 108
TsScanState function 116
4.7 RabbitNet Port 117
112 eDisplay (OP7200) 118
5. USING THE TCP/IP FEATURES 119
<Ctrl-Y> 120
5.2 TCP/IP Sample Programs 121
IP Address : 10.10.6.101 122
Netmask : 255.255.255.0 122
Default gateway : 10.10.6.1 122
Start > Run 123
118 eDisplay (OP7200) 124
5.3 Where Do I Go From Here? 125
120 eDisplay (OP7200) 126
CARE GUIDELINES 127
6.2 Installation Guidelines 128
6.3 Mounting Instructions 129
OP7200 Bezel/Gasket 130
6.4 Care Guidelines 131
126 eDisplay (OP7200) 132
APPENDIX A. SPECIFICATIONS 133
128 eDisplay (OP7200) 134
User’s Manual 129 135
A.1.1 Physical Mounting 136
A.2 Conformal Coating 137
A.3 Jumper Configurations 138
User’s Manual 133 139
134 eDisplay (OP7200) 140
Backup Battery 141
A.5 I/O Address Assignments 143
138 eDisplay (OP7200) 144
APPENDIX B. POWER SUPPLY 145
140 eDisplay (OP7200) 146
/RESET output signal 147
External 148
Figure B-4. VRAM Switch 150
B.3 Chip Select Circuit 151
146 eDisplay (OP7200) 152
APPENDIX C 153
DIGIN.C Sample Program 154
DIGOUT.C Sample Program 155
Jumpers: 156
H1: None 156
H2: As shown 156
APPENDIX D. RABBITNET 157
152 eDisplay (OP7200) 158
D.2 Physical Implementation 159
D.3 Function Calls 160
D.3.1 Status Byte 166
User’s Manual 161 167
162 eDisplay (OP7200) 168
User’s Manual 163 169
164 eDisplay (OP7200) 170
SCHEMATICS 171

Comments to this Manuals

No comments

Rabbit OP7100 User Manual Page 73

Comments to this Manuals

Related products and manuals for TVs & monitors Rabbit OP7100