Rabbit OP7100 User Manual Page 50
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
44 eDisplay (OP7200)
3.10 Programming Cable
The programming cable is used to connect the programming port of the RabbitCore module
to a PC serial COM port. The programming cable converts the RS-232 voltage levels used
by the PC serial port to the TTL voltage levels used by the Rabbit 2000.
When the PROG connector on the programming cable is connected to the RabbitCore
module’s programming header, programs can be downloaded and debugged over the serial
interface.
The DIAG connector of the programming cable may be used on the programming header of
the RabbitCore module with the module operating in the Run Mode. This allows the pro-
gramming port to be used as a regular serial port.
3.10.1 Changing Between Program Mode and Run Mode
The OP7200 is automatically in Program Mode when the PROG connector on the pro-
gramming cable is attached to the RabbitCore module, and is automatically in Run Mode
when no programming cable is attached. When the Rabbit 2000 is reset, the operating
mode is determined by the status of the SMODE pins. When the programming cable’s
PROG connector is attached, the SMODE pins are pulled high, placing the Rabbit 2000 in
the Program Mode. When the programming cable’s PROG connector is not attached, the
SMODE pins are pulled low, causing the Rabbit 2000 to operate in the Run Mode.
Figure 21. OP7200 Program Mode and Run Mode Set-Up
A program can be run in either mode, but can only be downloaded and debugged when the
OP7200 is in the Program Mode.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information on the pro-
gramming port and the programming cable.
Program Mode
Run Mode
RESET OP7200 when changing mode:
Cycle power off/on
after removing or attaching programming cable.
D23
D20
+PWR PWR +K OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 GND
IN12 IN13 IN14 IN15 /RST TXC RXC TXD RXD 485 +485 GND
J10
J15
IN16 IN17 IN18 AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 AIN7 AGND
IN0 IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11
J2
J6
J3
D23
D20
+PWR PWR +K OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 GND
IN12 IN13 IN14 IN15 /RST TXC RXC TXD RXD 485 +485 GND
J10
J15
IN16 IN17 IN18 AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 AIN7 AGND
IN0 IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11
J2
J6
J3
J1
CAUTION: Disconnect power
before making or removing
terminal connections.
J2
J6
J3
J10
PROG
1
1
1
1
E-Net
R-Net
1
USR PWR
LNK ACT
+
J1
CAUTION: Disconnect power
before making or removing
terminal connections.
J2
J6
J3
J10
PROG
1
1
1
1
E-Net
R-Net
1
USR PWR
LNK ACT
+
DIAG
PROG
Colored edge
To
PC COM port
Programming
Cable
- User’s Manual 1
- OP7200 User’s Manual 2
- TABLE OF CONTENTS 3
- Chapter 4. Software 47 4
- Appendix B. Power Supply 139 5
- Appendix D. RabbitNet 151 5
- Index 161 5
- Schematics 165 5
- 1. INTRODUCTION 7
- Table 1. OP7200 Models 8
- Figure 1. OP7200 Tool Kit 9
- A compat 10
- User’s Manual 5 11
- 1.4 CE Compliance 12
- User’s Manual 7 13
- 8 eDisplay (OP7200) 14
- 2. GETTING STARTED 15
- 10 eDisplay (OP7200) 16
- User’s Manual 11 17
- PC COM port 18
- 2.4 Installing Dynamic C 19
- 2.5 Starting Dynamic C 19
- 2.6 PONG.C 20
- 2.7 Where Do I Go From Here? 20
- 2.8 Remove Battery Tab 21
- SETRTCKB.C 21
- 16 eDisplay (OP7200) 22
- 3. SUBSYSTEMS 23
- 3.1 OP7200 Pinouts 24
- 3.2 Indicators 25
- 3.3 Digital I/O 26
- Digital Input Voltage 27
- SINKING OUTPUTS 28
- SOURCING OUTPUTS 28
- CAUTION: Disconnect power 29
- User’s Manual 25 31
- Table 4. Bipolar Voltages 33
- 3.4.3.1 Modes 34
- User’s Manual 29 35
- 30 eDisplay (OP7200) 36
- 32 eDisplay (OP7200) 38
- 3.5 Serial Communication 39
- 34 eDisplay (OP7200) 40
- 36 eDisplay (OP7200) 42
- ETHERNET 43
- DIAG connector on 44
- 3.6 Memory 45
- PRE-2006 OP7200 46
- CURRENT OP7200 46
- 3.8 Keypad 47
- 3.9 OP7200 CPLD 48
- User’s Manual 43 49
- 3.10 Programming Cable 50
- 3.11 Other Hardware 51
- 46 eDisplay (OP7200) 52
- 4. SOFTWARE 53
- 48 eDisplay (OP7200) 54
- 4.1.1.2 Upgrades 55
- 50 eDisplay (OP7200) 56
- User’s Manual 51 57
- 4.3 Sample Programs 58
- 54 eDisplay (OP7200) 60
- User’s Manual 55 61
- 56 eDisplay (OP7200) 62
- 4.4 OP7200 Libraries 63
- 4.5 OP7200 Function APIs 64
- 4.5.2 Digital I/O 65
- OUT0–OUT7) 65
- 60 eDisplay (OP7200) 66
- 4.5.3 LEDs 68
- User’s Manual 67 73
- 70 eDisplay (OP7200) 76
- 0 if successful 78
- User’s Manual 77 83
- User’s Manual 95 101
- PARAMETER 101
- SEE ALSO 101
- 4.5.7 Keypad Functions 102
- 1 when completed 106
- RETURN VALUE 108
- 102 eDisplay (OP7200) 108
- PARAMETERS 108
- TsScanState function 116
- 4.7 RabbitNet Port 117
- 112 eDisplay (OP7200) 118
- 5. USING THE TCP/IP FEATURES 119
- <Ctrl-Y> 120
- 5.2 TCP/IP Sample Programs 121
- IP Address : 10.10.6.101 122
- Netmask : 255.255.255.0 122
- Default gateway : 10.10.6.1 122
- Start > Run 123
- 118 eDisplay (OP7200) 124
- 5.3 Where Do I Go From Here? 125
- 120 eDisplay (OP7200) 126
- CARE GUIDELINES 127
- 6.2 Installation Guidelines 128
- 6.3 Mounting Instructions 129
- OP7200 Bezel/Gasket 130
- 6.4 Care Guidelines 131
- 126 eDisplay (OP7200) 132
- APPENDIX A. SPECIFICATIONS 133
- 128 eDisplay (OP7200) 134
- User’s Manual 129 135
- A.1.1 Physical Mounting 136
- A.2 Conformal Coating 137
- A.3 Jumper Configurations 138
- User’s Manual 133 139
- 134 eDisplay (OP7200) 140
- Backup Battery 141
- A.5 I/O Address Assignments 143
- 138 eDisplay (OP7200) 144
- APPENDIX B. POWER SUPPLY 145
- 140 eDisplay (OP7200) 146
- /RESET output signal 147
- External 148
- Figure B-4. VRAM Switch 150
- B.3 Chip Select Circuit 151
- 146 eDisplay (OP7200) 152
- APPENDIX C 153
- DIGIN.C Sample Program 154
- DIGOUT.C Sample Program 155
- Jumpers: 156
- H1: None 156
- H2: As shown 156
- APPENDIX D. RABBITNET 157
- 152 eDisplay (OP7200) 158
- D.2 Physical Implementation 159
- D.3 Function Calls 160
- D.3.1 Status Byte 166
- User’s Manual 161 167
- 162 eDisplay (OP7200) 168
- User’s Manual 163 169
- 164 eDisplay (OP7200) 170
- SCHEMATICS 171
Related products and manuals for TVs & monitors Rabbit OP7100
TVs & monitors Rabbit OP7100 User Manual
(41 pages)
(41 pages)
TVs & monitors Rabbit OP7100 User Manual
(126 pages)
(126 pages)
TVs & monitors Rabbit OP7100 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals